5707 Multi Tool open fire lighter with hanging chain creative fashion multi-function tool lighter

Size & nbsp; 5.5x 1.5cm approximately

It can be used with gas

Open fire lighter

Detailed introduction:

Gas filling method

1. When filling gas, there must be no Mars or fire around, to ensure safety. Do not add gas while smoking
2. Qualified butane gas should be used. Inferior gas may damage the lighter or reduce its service life
3. For ordinary models, please stand the lighter upside down, align the gas outlet of the gas bottle with the air inlet of the lighter, and press it with force for about 2 seconds each time
If the gas can not be filled, it may be that there is excess air left in the steam box. At this time, you can deflate. Use a small screwdriver to aim at the air inlet to deflate rapidly for 1-2 times, and then add gas
4. When adding gas, please loosen the screw cover of the air inlet with a slotted screwdriver, and then operate according to the above steps. After gas filling, screw cover can be leveled, not too tight
Otherwise, the cover will not be dense and the sound will not be clear, and the gas will escape. The hardcover loudspeakers should use special nozzles to add gas
5. When filling the gasoline engine, open the head cover, pull out and turn the movement upside down, lift the outer sponge, add a certain amount of gasoline, and after the gasoline penetrates into the inner sponge, cover the outer sponge, and then put it into the casing
6. After all kinds of lighters are refueled, it is necessary to wait at least 1 minute to adjust the temperature of the newly charged gas to room temperature, and the ignition can only be started after the residual gas attached to the lighters has volatilized completely. If the ignition operation is carried out immediately,
may cause the residual gas on the surface of the lighter to burn, causing unnecessary danger
If the flame height is too high or too low after the gas is replenished, it is normal to adjust the flame height appropriately.

Adjust the flame
1. When using, the flame height will change to a certain extent with the decrease of the air content of the product and the change of the ambient temperature. This is a normal phenomenon. You can adjust the flame height appropriately
2. When using, the normal flame height should be controlled within the range of 0; 5-2. 5 cm for windproof and direct impact lighters; 5-4.0 cm for the lighters of Lansheng, gasoline and open fire
3. If you need to adjust the height of the flame, please use a slotted screwdriver to align with the groove of the flame regulator; If the lighter itself is equipped with an adjusting ring, it can be adjusted directly with your fingers. Turn clockwise in the direction of the (-) arrow to lower the flame height; The flame height can be increased by turning in the direction of the (+) arrow, i.e. counter clockwise. Note: do not rotate counter clockwise for more than half a turn on the basis of normal flame height. Otherwise, the product may be damaged
4. The flame height of gasoline lighter should be controlled by adjusting the height of ignition wick. If the flame height is too high, you can use scissors to cut the wick a little; If the flame height is too low, pull out the wick properly.

Precautions
1. Keep away from children if it contains pressurized flammable gas
2. Do not puncture or throw the lighter into the fire;

3. Please use in a ventilated environment and pay attention to inflammables
4. The direction of the fire head is strictly prohibited to face, skin, clothing and other combustible substances, so as to avoid danger
5. When igniting, please identify the position of the fire outlet and press the ignition button moderately. Different styles of lighters are ignited in different ways: straight, side and side; The gasoline engine should quickly rub the grinding wheel, and the Langsheng engine should quickly rub the roller from right to left with its thumb
6. When using, if dust and other debris fall into the fire outlet, it should be forced to blow in time to remove the debris, otherwise it will cause poor fire
7. As soon as the cover of the engine is opened, the gas starts to escape. Therefore, when the ignition is not started, be sure to cover it tightly and keep it
8. This product is not suitable for lighting. Please do not burn for more than 1 minute to avoid scalding skin
9. Do not keep the lighter in a high temperature environment (50C / 122F) for a long time, and avoid direct sunlight for a long time, such as around the stove, outdoor closed unmanned car and trunk
10. Due to the limitation of combustion conditions in the area above 3000 meters above sea level, the ignition of windbreak and direct impact lighters may be greatly affected. At this time, it is recommended to use open fire lighter
11. When using the lighters of tabletop and other arts and crafts, it is necessary to make clear the positions of the fire outlet, press tap, air inlet and Flame regulator so as to use them correctly
12. Qualified butane gas should be used, and inferior gas may damage the lighters or reduce their service life.